Dewalt DC970K 2 Manual

The Dewalt DC970K 2 is a compact and lightweight cordless drill/driver designed for both professional and DIY users. It features a high-performance motor that delivers 380 unit watts out for maximum performance across a range of drilling and fastening applications. The drill is equipped with a 1/2-inch single sleeve ratcheting chuck for superior bit retention, and it has a two-speed transmission (0-450 & 0-1500 RPM) for increased versatility. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Operating the Drill 8. Maintenance 9. Safety Information 10. Troubleshooting

Features at a Glance

Key components: Compact design, high-performance motor, 1/2-inch chuck, two-speed transmission, and lightweight construction.

Feature	Description
High-performance motor	Delivers 380 unit watts out for maximum performance
1/2-inch chuck	Single sleeve ratcheting chuck for superior bit retention
Two-speed transmission	0-450 & 0-1500 RPM for increased versatility
Compact design	Lightweight and easy to handle
Battery compatibility	Compatible with 18V NiCad and Lithium-Ion batteries

Installation

Unpack and inspect the contents. Ensure all components are included.

Charge the battery: Use the provided charger to fully charge the battery before first use.
Insert the battery: Align the battery with the base of the drill and push until it clicks into place.
Attach drill bit: Open the chuck, insert the desired drill bit, and tighten securely.

WARNING! Always wear safety goggles when operating the drill.

First-Time Setup

Power on the drill and familiarize yourself with its controls.

Check battery charge: Ensure the battery is fully charged before use.
Set speed: Choose the appropriate speed setting based on the material being drilled.
Practice drilling: Use scrap material to practice drilling and fastening.

CAUTION! Ensure a stable work surface when operating the drill.

Specifications

Voltage: 18V.
Chuck Size: 1/2 inch.
Speed: Two-speed transmission (0-450 & 0-1500 RPM).
Weight: 5.2 lbs.
Battery Type: NiCad or Lithium-Ion.
Max Torque: 380 in-lbs.
Dimensions: 8.5 x 9.5 x 3.5 inches.

Controls and Settings

Access settings via the speed selector and torque adjustment ring. The drill features a forward/reverse switch for easy operation.

Controls: Speed selector, torque adjustment ring, forward/reverse switch, and trigger.

Connecting Devices

Ensure the drill is powered off before connecting any accessories.

Align the accessory with the chuck.
Open the chuck and insert the accessory.
Tighten the chuck to secure the accessory.

Tip: Always check that the accessory is securely fastened before use.

Operating the Drill

To operate the drill, pull the trigger to start drilling. Adjust the speed and torque as necessary.

Press the trigger to start the drill.
Adjust speed based on the material.
Release the trigger to stop.

WARNING! Keep hands clear of the drill bit while in operation.

Maintenance

Regular maintenance is essential for optimal performance.

Clean the drill after use to remove dust and debris.
Check battery contacts for corrosion and clean if necessary.
Store in a dry place to prevent moisture damage.

Safety Information

Always follow safety guidelines when using the drill.

Wear safety goggles and a dust mask.
Keep hands away from moving parts.
Do not operate in wet conditions.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Drill does not start	Battery not charged	Charge the battery and try again.
Bit slips in chuck	Chuck not tightened	Tighten the chuck securely.
Drill overheats	Continuous use	Allow the drill to cool down before resuming use.
Low power	Battery nearing end of life	Replace the battery with a new one.

Service: For assistance, contact Dewalt customer service.